Replacement lamp for Krones Contiform 3 Pro

Sat, 25 Jul 2026 05:58:15 +0800

Stop the Burn-out Cycle on Your PET Blowing Lines

If you’re running SIG Blomax or Krones Contiform 3 Pro lines, you know the drill. One minute everything is humming along, and the next, a lamp pops. It’s frustrating. Usually, it’s just a mix of brutal heat and constant vibration shaking the life out of the tubes. We got tired of seeing that happen, so we rebuilt our replacement lamps to actually hold up. Dealing with the heat To get those PET preforms to the right temperature before they blow, you need a ton of power. But that kind of heat density is a nightmare for the quartz envelope. Most tubes just can’t take it and start to bow. We used a heavier-wall quartz construction to keep things straight and sturdy. Just a heads-up: if you’re pushing these to the limit, keep an eye on your oven’s airflow. If your reflectors get clogged, the lamp will overheat, and no amount of reinforcement can save it from that. Built for the shake Most lamps don’t just “burn out”—they fail at the pinch seal or the connector. High-speed blowing machines vibrate like crazy, and those weak points just snap. We beefed up the end-caps to handle that mechanical stress. The best part? They’re drop-in replacements. You don’t have to mess with your wiring or change your footprint. We also tightened up the connector specs to stop the arcing that usually kills the ends of the lamp. The trade-off Here’s the honest truth: because the quartz is thicker, these lamps have a bit more thermal inertia. That means they take a few extra seconds to hit full temp when you first flip the switch. You might need to tweak your warm-up timers slightly. But once they’re up and running? They’re rock solid. You get a steady heat that kills off those annoying “cold-spots” in your preforms. Fewer rejected bottles, less scrap on the floor, and way less time spent replacing bulbs.

Replacement IR bulb for Krones Contiform S

Sun, 19 Jul 2026 19:29:24 +0800

Stop Dealing with Constant Tube Burnouts

If you’re running SIG Blomax or Krones Contiform S lines, you know the drill. You’re in the middle of a run and—bam—another tube burns out. It’s usually a mix of thermal stress and those constant machine vibrations that just shake everything to pieces. We got tired of seeing that happen, so we built replacement IR bulbs that actually hold up. They aren’t fancy; they’re just tougher. They drop right into your existing setup to keep your heating steady and keep your line moving. Let’s talk about the heat. These lamps are designed to push a lot of wattage into a small space. We bumped up the voltage spec so you get that intense, short-wave IR output that hits the core of the PET preform fast. You don’t need a massive array of bulbs to get the job done. One heads-up, though: running these at full tilt puts a real load on your power supply. Just double-check that your transformers can handle the draw. If they can’t, you’re just asking for the filaments to snap early. Built for the shop floor Standard quartz just doesn’t cut it when a machine is vibrating 24/7. We switched to a reinforced glass blend that can take a beating without snapping. We also obsessed over the end caps. Why? Because a loose fit leads to electrical arcing, and arcing fries your connectors. Our lamps fit tight. No wiggle room, no sparks, just a solid connection. Getting them running Swapping these in is easy. Pull the dead tube, wire these in, and you’re back in business. Since they’re tougher than the OEM parts, you’ll notice way fewer “broken tube” alarms popping up on your HMI. It’s a relief not to be chasing those errors all shift. The only thing to watch for is the light spectrum. It’s a little different than the originals. You might need to tweak your heating zone timers by a few milliseconds to get your bottle wall thickness exactly where you want it. Once you dial that in, you’re golden.

Contiform on Professional IR Heating Ware

Replacement lamp for Krones Contiform 3 Pro

Stop the Burn-out Cycle on Your PET Blowing Lines

Replacement IR bulb for Krones Contiform S

Stop Dealing with Constant Tube Burnouts